Loopback Encrypted Filesystem HOWTO Copyright by Ryan T. Rhea, rhear@cs.winthrop.edu v1.1, 29 November 1999 This document explains how to setup and then use a filesystem that, when mounted by a user, dynamically and transparently encrypts its contents. The filesystem is stored in a regular file, which can be hidden or named non-conspicuously such that it would most likely be overlooked. This allows for a high level of secure storage of data. ______________________________________________________________________ Table of Contents 1. Before you begin 2. Introduction 3. Summary 4. Details ______________________________________________________________________ 1. Before you begin This process requires the kernel source code, knowledge of compiling this code, and a lot of patience. I highly recommend having a boot disk ready. Also, be sure to have a backup before you permanently store your important data on the encrypted filesystem - it can be corrupted like any other filesystem. As a minimum, you will have to patch to at least version 2.2.9 of the linux kernel before continuing. There are further instructions on applying patches in the ``'' section later in this document. Kernel source can be found at: There is a HOWTO on the process of recompiling kernels at: This document may be reproduced and distributed in whole or in part, without fee, subject to the following conditions: o The copyright notice and this permission notice must be preserved complete on all complete or partial copies. o Any translation or derived work must be approved by the author in writing before distribution. o If you distribute this work in part, instructions for obtaining he complete version of this manual must be included, and a means for obtaining a complete version provided. o All source code in this document is placed under the GNU General Public License, available via anonymous FTP from: 2. Introduction The process uses the device '/dev/loop*' (where * can be 0-7 on most installations) to mount a loopback filesystem. The same process can be used without encryption to store a linux filesystem on a non-linux partition. There is a HOWTO on this at the LDP site mentioned previously. Different types of encryption can be used, including XOR, DES, twofish, blowfish, cast128, serpent, MARS, RC6, DFC, and IDEA. The program 'losetup' (loopback setup) is what associates your encrypted file with a filesystem and it's cipher type. According to Alexander Kjeldaas, who maintains kerneli.org and the international crypto patches, DES and losetup are currently incompatible. This is due to differences in the way the two handle parity bits. There are no plans to support DES as it is much more insecure than the other ciphers. Twofish, blowfish, cast128, and serpent are all licensed free for any use. The others may or may not have licensing restrictions. Several of them are candidates for the AES standard. The finalists will provide royalty free use of their ciphers worldwide. This document uses the serpent algorithm because it is strong yet remarkably fast, and it's freely distributable under the GPL. According to it's documentation, serpent uses a 128-bit block cipher designed by Ross Anderson, Eli Biham and Lars Knudsen. It provides users with the highest practical level of assurance that no shortcut attacks will be found. The documentation on serpent as well as the source code can be found at: Also, this document assumes that the ciphers are compiled directly into the kernel. You may install them as modules, but the technique is not discussed in this document. You will have to edit the file process is discussed in detail in the kernel compilation HOWTO referenced previously. 3. Summary There are many steps involved in the process. I will provide ``'' for these steps in the next section. I thought it would be nice to provide a summary first to provide reference (if you are experienced with unix/linux you probably don't need the details anyway). Here they are summarized as follows: 1. Download the newest international crypto patch (I used 2. Patch the kernel 3. Run 'config' (or 'menuconfig' or 'xconfig') to configure your are scattered. First of all, before you will see any other options you must enable 'Prompt for development and/or incomplete code/drivers' under 'Code Maturity level options'. Under 'Crypto options' enable 'crypto ciphers' and serpent, but try whatever you want. Remember that DES is known to be incompatible as of 2.2.10.4 - it may never be supported at all. There are several important options to select under 'Block Devices'. These include device support', 'Use relative block numbers as basis for transfer functions (RECOMMENDED)', and 'General encryption support'. DO NOT select the crypto options under the various network categories. I will not go any further into configuration of the kernel, it is out of the scope of this document and can be found at the LDP site. 4. Compile the new kernel. 5. Edit '/etc/lilo.conf' to add the new kernel image. Run add the kernel to the boot loader. 6. Download the source for the newest 'util-linux' (I used 7. Extract the 'util-linux' source. 8. Apply the corresponding patch found in your 9. CAREFULLY read the 'INSTALL' file! This package contains the sources for many system dependent files (important tools such as MCONFIG file before compiling these sources have a boot disk and/or shotgun ready because your system will be quite confused. Basically you want to set almost all of the 'HAVE_*' fields equal to yes so that the important authentication tools are not compiled and written over. The tools you do want rebuilt are 'mount' and 'losetup' to accommodate the new encryption schemes. I suggest that you refer to the ``'' section below for this step. 10. Compile and install the 'util-linux' source 11. Reboot the machine with the new kernel. 12. Edit '/etc/fstab', adding an entry for your mount point as follows: ______________________________________________________________________ /dev/loop0 /mnt/crypt ext2 user,noauto,rw,loop 0 0 ______________________________________________________________________ 13. Create the directory that will hold your filesystem, as in 14. As the user, create your encrypted file as follows: dd if=/dev/urandom of=/etc/cryptfile bs=1M count=10 15. Run losetup as follows: losetup -e serpent /dev/loop0 /etc/cryptfile You only have one chance to enter the password, be careful. If you want to double-check your password, you can use the command: losetup -d /dev/loop0 This will deactivate your loop device. Next you will run losetup again to test your password, as follows: losetup -e serpent /dev/loop0 /etc/cryptfile 16. Make your ext2 filesystem as follows: mkfs -t ext2 /dev/loop0 17. Now you can mount the encrypted filesystem with: mount -t ext2 /dev/loop0 /mnt/crypt 18. When your done, you want to unmount and protect your filesystem as follows: umount /dev/loop0 losetup -d /dev/loop0 4. Details Kernel Patches: You can upgrade from '2.2.x' releases by patching. Each patch that is released for '2.2.x' contains bugfixes. New features will be added to the Linux '2.3.x' development kernel. To install by patching, get all the newer patch files and do the following: cd /usr/src gzip -cd patchXX.gz | patch -p0 Repeat xx for all versions bigger than the version of your current source tree, IN ORDER. The default directory for the kernel source is '/usr/src/linux'. If your source is installed somewhere else, I would suggest using a symbolic link from '/usr/src/linux'. Editing 'MCONFIG' for the 'util-linux' package compilation: The following are excerpts from the 'MCONFIG' file I used to compile the 'util-linux' package. Note that this is fairly specific for my setup, which is loosely based on RedHat 5.2. The point is to make sure you don't overwrite any important system tools such as 'login', 'getty', or 'passwd'. Anyway, here are the important lines as follows: ______________________________________________________________________ CPU=$(shell uname -m | sed s/I.86/intel/) LOCALEDIR=/usr/share/locale HAVE_PAM=no HAVE_SHADOW=yes HAVE_PASSWD=yes REQUIRE_PASSWORD=yes ONLY_LISTED_SHELLS=yes HAVE_SYSVINIT=yes HAVE_SYSVINIT_UTILS=yes HAVE_GETTY=yes USE_TTY_GROUP=yes HAVE_RESET=yes HAVE_SLN=yes CC=gcc ______________________________________________________________________ Suggestions: Note that you could use any of the eight loopback devices, from to '/dev/loop7'. Use an inconspicuous directory for the mount point. I would suggest creating a folder with 700 permissions inside your home folder. The same goes for the file that holds the data. I use a filename like 'sysfile' or 'config.data' inside the '/etc' folder. This will usually get overlooked. I created very simple Perl scripts to mount and unmount the filesystem with one command. Write these, make them executable (chmod u+x), and store them somewhere in your path. ______________________________________________________________________ #!/usr/bin/perl -w # #minimal utility to setup loopback encryption filesystem #Copyright 1999 by Ryan T. Rhea `losetup -e serpent /dev/loop0 /etc/cryptfile`; `mount /mnt/crypt`; ______________________________________________________________________ Name the above script 'loop', and then you can be on your way with one command ('loop') and a password. ______________________________________________________________________ #!/usr/bin/perl -w # #minimal utility to deactivate loopback encryption filesystem #Copyright 1999 by Ryan T. Rhea `umount /mount/crypt`; `losetup -d /dev/loop0`; ______________________________________________________________________ Name the second one 'unloop', and then typing 'unloop' will quickly deactivate your filesystem.