*BETA Versions*
 V0.92    * MCA-Devices included
          * EISA-Devices included, but the names are not shown yet
          * Partitiontable included

 V0.9     * first PM Version of PM WHY/2
          * this version will only run in january 1998 (!!)
          * the following windows/function are not implemented yet:
            - Motherboard
            - Hardware Manager
            - EISA
            - MCA
            - EIDE
            - SCSI
            - Partitions
	    these pages will follow in the next releases.
          * also it is not possible to save or print any data !
          * you cannot save any settings now or turn off any testing !!
          * Benchmarking is not planned to include, use SysBench/2 instead
          * also detection refresh rates of video modes won't be included
          * right now I don't know a method to detect the 
            clock frequency or the cache size under os/2 :((

 V0.28.11 * first OS/2 Version
          * DOS-Version (all before) will NOT (!!) be continued

 V0.07.31 * more PCI-devices
          * more CPUs
          * fixed some more bugs

 V0.05.20 * some more bugs in video-benchmark removed
          * video-benchmark now uses size of 1st cache for testing
          * video-benchmark won't run if virtual-processor-mode !!
          * Processormode added into hardware-window

 V0.05.14 * some bugs in video-benchmark removed
          * PnP-window removed

 V0.05.05 * bug in adding benchmark results corrected
          * PCI-display changed
          * WHY.DAT extended

 V0.05.03 * some small bugfixes

 V0.05.02 * Additional Graphicsbenchmark added (1st version)

 V0.04.30 * corrected E/IDE-Harddiskdetection (no CD-ROM included!!)
            Display extended for Ultra-DMA and ATA-Version
          * some more program faults have been fixed
          * CMOS-table corrected (Harddisktypes)

 V0.04.28 * Memoryproblem of "new Hardwaredetection" solved

 V0.04.23 * Some program faults have been fixed

 V0.04.21 * Benchmark-submenu moved to own menu, with extended editor

          * The HD-Benchmark should now detect the correct Harddiskname of
              the testet partition. This works except the SCSI-Drives
              are before the IDE-Drives (if the BIOS is supporting this),
              and if the test will be performed on a partition on the
              >=2nd harddisk, and the geometrie-data is the same as a
              partition on the 1st harddisk !!

            Der HD-Benchmark sollte nun den richtigen Plattennamen zur
              getesteten Partition erkennen. Ausgenommen sind Flle, wenn
              sich die SCSI-Platten vor den IDE befinden (falls dies das
              BIOS berhaupt untersttzt), und falls zufllig eine Partition
              auf der >=2. Platte stattfindet, und diese die gleichen
              Geometriedaten wie die 1. Platte hat !!

            ATTENTION: If you use the HD-Benchmarktest defragment your
              Harddisk in any case. If the display stops a little bit,
              during the creation of the testfile, this file was NOT
              created in one part => the results CANNOT be compared !!!

          * Bug in partitiontable fixed,
              and the Output is extended to show extended Partitions, too.
              Also there is now an additional fied, that says if this is
              a extended or primary partition.

 V0.04.20 * HD-Benchmark-middle is now weighted a la c't:
              60%-reading:40%-writing

 V0.04.19 * Save- and Print-Dialog crash the system - fixed

 V0.04.18 * Benchmarks corrected

 V0.04.17 * The HD-Benchmark results will now be displayed
          * If SmartDrive or Hyperdisk are detected, you will be asked, if
            you want to continue the HD-Benchmark or not

 V0.04.16 * New Benchmarks:
              - The Harddiskbenchmark will now start at the programstart,
                please take a look to the change I made for the variable
                "HDSpeedNumber" in WHY.INI !!!
                Also the benchmark is now based on the c't-harddisk-
                benchmarkprogram (a german magazine) and the value "Middle"
                shows the weighted middle of the data-throughput !!
              - The c't benchmarks HLPAS have also been included as good as
                possible, as well as the "Appel-Graphic-Calculation". These
                two can be turned on or off by the variable "CPUSpeed".
                And the results can be found in a new section of the
                benchmark-window: "This Computer"

            All these benchmarks should give you a better comparisson, also
            the values are very close to the results of the german
            c't-magazine !! ;-)
            A little fault is new too:
              Because of the fact, that the test run in real Partitions now,
              the name of the corresponding harddisk may be wrong. This will
              be corrected as soon as possible in one of the next version !!!
            On standard startup, the harddisk-benchmark will be disabled, so
            you can manually setup which drives to test and which not!
            (WHY.INI)
          * corrected WHY.DAT for Cyrix 6x86

 V0.04.14 * Helpfile added
          * some small bugs removed
          * Plug&Play-BIOS added, but no devices will be shown !!

 V0.04.06 * new Graphic-chipsets added : Alliance, ARK, ATI, S3, Trident,
            Cirrus Logic, NVidia and Rendition
          * PCI-Device-Detection changed
          * corrected and extented WHY.DAT
            (TX-Chipset added)

 V0.04.05 * The CPU-PR-Relation wasn't working correctly and could end in
            an endless loop !! Fixed !!

 V0.03.17 * The Chipsetdetection moved into WHYCHIP.DAT, an ASCII-File.
            This file can now be corrected and extended as WHY.DAT !!
          * The integrated editor is extented to edit WHY.DAT and
            WHYCHIP.DAT.

 V0.03.14 * If SCSI-CAM is detected, the IDE-part will be disabled !!
          * An integrated editor for WHY.INI added !

 V0.03.13 * Restart of Hardwaredetection is working
          * Attention !!! If you have NCR-version 3.07 and IDE-Devices in
            the same system, WHY will crash if you exit it: it cannot find
            COMMAND.COM any more (this was on my system). NCR-BIOS-Version
            4.x will solve this problem, but you wont have CAM anymore,
            only ASPI !
            Disable the IDE-Detection will work too !

 V0.03.12 * SCSI-CAM-Detection is included, only SCSI-Type and Device-
            Capacity are missing yet.
          * Hopefully there are no more problems with older PCI-Boards,
            PCI-detection for those changed.
            This is only a test. Please report if the PCI-Devices are
            displayed or not !!

 V0.02.24 * corrected details on HD-BIOS datas of SCSI-HDs

 V0.02.19 * corrected CPU-Identification of Cyrix CPUs
          * corrected WHY.DAT

 V0.02.17 * stupid BUG, all CPUID-CPUs are Intel
          * CAM-detection is removed from source for now,
            corresponding part WHY.INI is now without effect !

 V0.02.16 * new and extended WHY.DAT
          * new Matrox Graphiccards added
          * corrected display of VESA-Modi 

 V0.02.14 * corrected capacity data of ASPI-devices
          * corrected Clock-Frequency data of Co-Processors
          * new WHY.DAT
          * corrected some Processor Identification strings
          * possibility to deactivate detection of SCSI-CAM-devices
            in WHY.INI (CAM is untested!! Errors in source are possible)

 V0.02.13 * CPU-Identification moved into WHY.DAT
          * knowledge of MMX-CPUs
          * WHY.DAT is now a editable and extendable ASCII-File


