/* $NetBSD: nslm7x.c,v 1.73.2.2 2023/01/19 10:40:25 martin Exp $ */ /*- * Copyright (c) 2000 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Bill Squier. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ #include __KERNEL_RCSID(0, "$NetBSD: nslm7x.c,v 1.73.2.2 2023/01/19 10:40:25 martin Exp $"); #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #if defined(LMDEBUG) #define DPRINTF(x) do { printf x; } while (0) #else #define DPRINTF(x) #endif /* * LM78-compatible chips can typically measure voltages up to 4.096 V. * To measure higher voltages the input is attenuated with (external) * resistors. Negative voltages are measured using inverting op amps * and resistors. So we have to convert the sensor values back to * real voltages by applying the appropriate resistor factor. */ #define RFACT_NONE 10000 #define RFACT(x, y) (RFACT_NONE * ((x) + (y)) / (y)) #define NRFACT(x, y) (-RFACT_NONE * (x) / (y)) #define LM_REFRESH_TIMO (2 * hz) /* 2 seconds */ static const struct wb_product *wb_lookup(struct lm_softc *, const struct wb_product *, uint16_t); static int wb_match(struct lm_softc *); static int wb_attach(struct lm_softc *); static int nslm_match(struct lm_softc *); static int nslm_attach(struct lm_softc *); static int def_match(struct lm_softc *); static int def_attach(struct lm_softc *); static void wb_temp_diode_type(struct lm_softc *, int); static uint16_t wb_read_vendorid(struct lm_softc *); static void lm_refresh(void *); static void lm_generic_banksel(struct lm_softc *, uint8_t); static void lm_setup_sensors(struct lm_softc *, const struct lm_sensor *); static void lm_refresh_sensor_data(struct lm_softc *); static void lm_refresh_volt(struct lm_softc *, int); static void lm_refresh_temp(struct lm_softc *, int); static void lm_refresh_fanrpm(struct lm_softc *, int); static void wb_refresh_sensor_data(struct lm_softc *); static void wb_w83637hf_refresh_vcore(struct lm_softc *, int); static void wb_refresh_nvolt(struct lm_softc *, int); static void wb_w83627ehf_refresh_nvolt(struct lm_softc *, int); static void wb_refresh_temp(struct lm_softc *, int); static void wb_refresh_fanrpm(struct lm_softc *, int); static void wb_w83792d_refresh_fanrpm(struct lm_softc *, int); static void wb_nct6776f_refresh_fanrpm(struct lm_softc *, int); static void as_refresh_temp(struct lm_softc *, int); struct lm_chip { int (*chip_match)(struct lm_softc *); int (*chip_attach)(struct lm_softc *); }; static struct lm_chip lm_chips[] = { { wb_match, wb_attach }, { nslm_match, nslm_attach }, { def_match, def_attach } /* Must be last */ }; /* LM78/78J/79/81 */ static const struct lm_sensor lm78_sensors[] = { /* Voltage */ { .desc = "VCore A", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VCore B", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(68, 100) }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = lm_refresh_volt, .rfact = RFACT(30, 10) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = lm_refresh_volt, .rfact = NRFACT(240, 60) }, { .desc = "-5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = lm_refresh_volt, .rfact = NRFACT(100, 60) }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = lm_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = lm_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = lm_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W83627HF */ static const struct lm_sensor w83627hf_sensors[] = { /* Voltage */ { .desc = "VCore A", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VCore B", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 50) }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = lm_refresh_volt, .rfact = RFACT(28, 10) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = wb_refresh_nvolt, .rfact = RFACT(232, 56) }, { .desc = "-5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = wb_refresh_nvolt, .rfact = RFACT(120, 56) }, { .desc = "5VSB", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x50, .refresh = lm_refresh_volt, .rfact = RFACT(17, 33) }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x51, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Temp2", .type = ENVSYS_STEMP, .bank = 2, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W8627EHF */ /* * The W83627EHF can measure voltages up to 2.048 V instead of the * traditional 4.096 V. For measuring positive voltages, this can be * accounted for by halving the resistor factor. Negative voltages * need special treatment, also because the reference voltage is 2.048 V * instead of the traditional 3.6 V. */ static const struct lm_sensor w83627ehf_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT(56, 10) / 2 }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "VIN3", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = wb_w83627ehf_refresh_nvolt, .rfact = 0 }, { .desc = "VIN5", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, { .desc = "VIN6", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, { .desc = "3.3VSB", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x50, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x51, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, { .desc = "VIN8", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x52, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Temp2", .type = ENVSYS_STEMP, .bank = 2, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W83627DHG */ static const struct lm_sensor w83627dhg_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT(56, 10) / 2 }, { .desc = "AVCC", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = wb_w83627ehf_refresh_nvolt, .rfact = 0 }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = lm_refresh_volt, .rfact = 16000 }, { .desc = "VIN3", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3VSB", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x50, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x51, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, /* Temperature */ { .desc = "MB Temperature", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "CPU Temperature", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Aux Temp", .type = ENVSYS_STEMP, .bank = 2, .reg = 0x50, .refresh = lm_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "System Fan", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "CPU Fan", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Aux Fan", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W83637HF */ static const struct lm_sensor w83637hf_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = wb_w83637hf_refresh_vcore, .rfact = 0 }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT(28, 10) }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 51) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = wb_refresh_nvolt, .rfact = RFACT(232, 56) }, { .desc = "5VSB", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x50, .refresh = lm_refresh_volt, .rfact = RFACT(34, 51) }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x51, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Temp2", .type = ENVSYS_STEMP, .bank = 2, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W83697HF */ static const struct lm_sensor w83697hf_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 50) }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = lm_refresh_volt, .rfact = RFACT(28, 10) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = wb_refresh_nvolt, .rfact = RFACT(232, 56) }, { .desc = "-5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = wb_refresh_nvolt, .rfact = RFACT(120, 56) }, { .desc = "5VSB", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x50, .refresh = lm_refresh_volt, .rfact = RFACT(17, 33) }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x51, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W83781D */ /* * The datasheet doesn't mention the (internal) resistors used for the * +5V, but using the values from the W83782D datasheets seems to * provide sensible results. */ static const struct lm_sensor w83781d_sensors[] = { /* Voltage */ { .desc = "VCore A", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VCore B", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 50) }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = lm_refresh_volt, .rfact = RFACT(28, 10) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = lm_refresh_volt, .rfact = NRFACT(2100, 604) }, { .desc = "-5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = lm_refresh_volt, .rfact = NRFACT(909, 604) }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Temp2", .type = ENVSYS_STEMP, .bank = 2, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = lm_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = lm_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = lm_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W83782D */ static const struct lm_sensor w83782d_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VINR0", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 50) }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = lm_refresh_volt, .rfact = RFACT(28, 10) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = wb_refresh_nvolt, .rfact = RFACT(232, 56) }, { .desc = "-5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = wb_refresh_nvolt, .rfact = RFACT(120, 56) }, { .desc = "5VSB", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x50, .refresh = lm_refresh_volt, .rfact = RFACT(17, 33) }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x51, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Temp2", .type = ENVSYS_STEMP, .bank = 2, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W83783S */ static const struct lm_sensor w83783s_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 50) }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = lm_refresh_volt, .rfact = RFACT(28, 10) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = wb_refresh_nvolt, .rfact = RFACT(232, 56) }, { .desc = "-5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = wb_refresh_nvolt, .rfact = RFACT(120, 56) }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W83791D */ static const struct lm_sensor w83791d_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = 10000 }, { .desc = "VINR0", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = 10000 }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = 10000 }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 50) }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = lm_refresh_volt, .rfact = RFACT(28, 10) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = wb_refresh_nvolt, .rfact = RFACT(232, 56) }, { .desc = "-5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = wb_refresh_nvolt, .rfact = RFACT(120, 56) }, { .desc = "5VSB", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0xb0, .refresh = lm_refresh_volt, .rfact = RFACT(17, 33) }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0xb1, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VINR1", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0xb2, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 0, .reg = 0xc0, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Temp2", .type = ENVSYS_STEMP, .bank = 0, .reg = 0xc8, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan3", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0xba, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan4", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0xbb, .refresh = wb_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* W83792D */ static const struct lm_sensor w83792d_sensors[] = { /* Voltage */ { .desc = "VCore A", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VCore B", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "-5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = wb_refresh_nvolt, .rfact = RFACT(120, 56) }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = lm_refresh_volt, .rfact = RFACT(28, 10) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = wb_refresh_nvolt, .rfact = RFACT(232, 56) }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = lm_refresh_volt, .rfact = RFACT(34, 50) }, { .desc = "5VSB", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0xb0, .refresh = lm_refresh_volt, .rfact = RFACT(17, 33) }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0xb1, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 0, .reg = 0xc0, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Temp2", .type = ENVSYS_STEMP, .bank = 0, .reg = 0xc8, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = wb_w83792d_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = wb_w83792d_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = wb_w83792d_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan3", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0xb8, .refresh = wb_w83792d_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan4", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0xb9, .refresh = wb_w83792d_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan5", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0xba, .refresh = wb_w83792d_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan6", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0xbe, .refresh = wb_w83792d_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* AS99127F */ static const struct lm_sensor as99127f_sensors[] = { /* Voltage */ { .desc = "VCore A", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VCore B", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 50) }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = lm_refresh_volt, .rfact = RFACT(28, 10) }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = wb_refresh_nvolt, .rfact = RFACT(232, 56) }, { .desc = "-5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = wb_refresh_nvolt, .rfact = RFACT(120, 56) }, /* Temperature */ { .desc = "Temp0", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Temp1", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = as_refresh_temp, .rfact = 0 }, { .desc = "Temp2", .type = ENVSYS_STEMP, .bank = 2, .reg = 0x50, .refresh = as_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "Fan0", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x28, .refresh = lm_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan1", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x29, .refresh = lm_refresh_fanrpm, .rfact = 0 }, { .desc = "Fan2", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x2a, .refresh = lm_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* NCT6776F */ static const struct lm_sensor nct6776f_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x20, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, { .desc = "+12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x21, .refresh = lm_refresh_volt, .rfact = RFACT(56, 10) / 2 }, { .desc = "AVCC", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x22, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x23, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "-12V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x24, .refresh = wb_w83627ehf_refresh_nvolt, .rfact = 0 }, { .desc = "+5V", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x25, .refresh = lm_refresh_volt, .rfact = 16000 }, { .desc = "VIN3", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x26, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3VSB", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x50, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 5, .reg = 0x51, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, /* Temperature */ { .desc = "MB Temperature", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x27, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "CPU Temperature", .type = ENVSYS_STEMP, .bank = 1, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Aux Temp", .type = ENVSYS_STEMP, .bank = 2, .reg = 0x50, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "System Fan", .type = ENVSYS_SFANRPM, .bank = 6, .reg = 0x56, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "CPU Fan", .type = ENVSYS_SFANRPM, .bank = 6, .reg = 0x58, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "Aux Fan0", .type = ENVSYS_SFANRPM, .bank = 6, .reg = 0x5a, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "Aux Fan1", .type = ENVSYS_SFANRPM, .bank = 6, .reg = 0x5c, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "Aux Fan2", .type = ENVSYS_SFANRPM, .bank = 6, .reg = 0x5e, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* NCT610[246]D */ static const struct lm_sensor nct6102d_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x00, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VIN0", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x01, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "AVCC", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x02, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "3VCC", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x03, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "VIN1", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x04, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VIN2", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x05, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "+3.3VSB", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x07, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x08, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "VTT", .type = ENVSYS_SVOLTS_DC, .bank = 0, .reg = 0x09, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, /* Temperature */ { .desc = "MB Temperature", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x18, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "CPU Temperature", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x19, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "Aux Temp", .type = ENVSYS_STEMP, .bank = 0, .reg = 0x1a, .refresh = lm_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "System Fan", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x30, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "CPU Fan", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x32, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "Aux Fan", .type = ENVSYS_SFANRPM, .bank = 0, .reg = 0x34, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; /* NCT6779D */ static const struct lm_sensor nct6779d_sensors[] = { /* Voltage */ { .desc = "VCore", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x80, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, { .desc = "VIN1", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x81, .refresh = lm_refresh_volt, .rfact = RFACT(56, 10) / 2 }, { .desc = "AVCC", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x82, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "+3.3V", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x83, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "VIN0", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x84, .refresh = lm_refresh_volt, .rfact = RFACT(48600, 10000) }, { .desc = "VIN8", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x85, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, { .desc = "VIN4", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x86, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "+3.3VSB", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x87, .refresh = lm_refresh_volt, .rfact = RFACT(34, 34) / 2 }, { .desc = "VBAT", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x88, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VTT", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x89, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VIN5", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x8a, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VIN6", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x8b, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VIN2", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x8c, .refresh = lm_refresh_volt, .rfact = RFACT_NONE }, { .desc = "VIN3", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x8d, .refresh = lm_refresh_volt, .rfact = RFACT(14414, 10000) }, { .desc = "VIN7", .type = ENVSYS_SVOLTS_DC, .bank = 4, .reg = 0x8e, .refresh = lm_refresh_volt, .rfact = RFACT_NONE / 2 }, /* Temperature */ { .desc = "MB Temperature", .type = ENVSYS_STEMP, .bank = 4, .reg = 0x90, .refresh = lm_refresh_temp, .rfact = 0 }, { .desc = "CPU Temperature", .type = ENVSYS_STEMP, .bank = 4, .reg = 0x91, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Aux Temp0", .type = ENVSYS_STEMP, .bank = 4, .reg = 0x92, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Aux Temp1", .type = ENVSYS_STEMP, .bank = 4, .reg = 0x93, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Aux Temp2", .type = ENVSYS_STEMP, .bank = 4, .reg = 0x94, .refresh = wb_refresh_temp, .rfact = 0 }, { .desc = "Aux Temp3", .type = ENVSYS_STEMP, .bank = 4, .reg = 0x95, .refresh = wb_refresh_temp, .rfact = 0 }, /* Fans */ { .desc = "System Fan", .type = ENVSYS_SFANRPM, .bank = 4, .reg = 0xc0, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "CPU Fan", .type = ENVSYS_SFANRPM, .bank = 4, .reg = 0xc2, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "Aux Fan0", .type = ENVSYS_SFANRPM, .bank = 4, .reg = 0xc4, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "Aux Fan1", .type = ENVSYS_SFANRPM, .bank = 4, .reg = 0xc6, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = "Aux Fan2", .type = ENVSYS_SFANRPM, .bank = 4, .reg = 0xc8, .refresh = wb_nct6776f_refresh_fanrpm, .rfact = 0 }, { .desc = NULL } }; static const struct wb_product wb_products[] = { { WB_CHIPID_W83627HF, "W83627HF", w83627hf_sensors, NULL }, { WB_CHIPID_W83627THF, "W83627THF",w83637hf_sensors, NULL }, { WB_CHIPID_W83627EHF_A,"W83627EHF-A",w83627ehf_sensors,NULL }, { WB_CHIPID_W83627EHF, "W83627EHF",w83627ehf_sensors,NULL }, { WB_CHIPID_W83627DHG, NULL, NULL, NULL }, { WB_CHIPID_W83637HF, "W83637HF", w83637hf_sensors, NULL }, { WB_CHIPID_W83697HF, "W83697HF", w83697hf_sensors, NULL }, { WB_CHIPID_W83781D, "W83781D", w83781d_sensors, NULL }, { WB_CHIPID_W83781D_2, "W83781D", w83781d_sensors, NULL }, { WB_CHIPID_W83782D, "W83782D", w83782d_sensors, NULL }, { WB_CHIPID_W83783S, "W83783S", w83783s_sensors, NULL }, { WB_CHIPID_W83791D, "W83791D", w83791d_sensors, NULL }, { WB_CHIPID_W83791SD, "W83791SD", NULL, NULL }, { WB_CHIPID_W83792D, "W83792D", w83792d_sensors, NULL }, { WB_CHIPID_AS99127F, NULL, NULL, NULL }, { 0, NULL, NULL, NULL } }; static const struct wb_product wbsio_products[] = { { WBSIO_ID_W83627DHG, "W83627DHG",w83627dhg_sensors,NULL }, { WBSIO_ID_NCT6775F, "NCT6775F", nct6776f_sensors, NULL }, { WBSIO_ID_NCT6776F, "NCT6776F", nct6776f_sensors, NULL }, { WBSIO_ID_NCT5104D, "NCT5104D or 610[246]D",nct6102d_sensors,NULL }, { WBSIO_ID_NCT6779D, "NCT6779D", nct6779d_sensors, NULL }, { WBSIO_ID_NCT6791D, "NCT6791D", nct6779d_sensors, NULL }, { WBSIO_ID_NCT6792D, "NCT6792D", nct6779d_sensors, NULL }, { WBSIO_ID_NCT6793D, "NCT6793D", nct6779d_sensors, NULL }, { WBSIO_ID_NCT6795D, "NCT6795D", nct6779d_sensors, NULL }, { WBSIO_ID_NCT6796D, "NCT6796D", nct6779d_sensors, NULL }, { WBSIO_ID_NCT6797D, "NCT6797D", nct6779d_sensors, NULL }, { WBSIO_ID_NCT6798D, "NCT6798D", nct6779d_sensors, NULL }, { WBSIO_ID_NCT6799D, "NCT6799D", nct6779d_sensors, NULL }, { 0, NULL, NULL, NULL } }; static const struct wb_product as99127f_products[] = { { WB_VENDID_ASUS, "AS99127F", w83781d_sensors, NULL }, { WB_VENDID_WINBOND, "AS99127F rev 2",as99127f_sensors,NULL }, { 0, NULL, NULL, NULL } }; static void lm_generic_banksel(struct lm_softc *lmsc, uint8_t bank) { (*lmsc->lm_writereg)(lmsc, WB_BANKSEL, bank); } /* * bus independent match * * prerequisites: lmsc contains valid lm_{read,write}reg() routines * and associated bus access data is present in attachment's softc */ int lm_match(struct lm_softc *lmsc) { uint8_t cr; int i, rv; /* Perform LM78 reset */ /*(*lmsc->lm_writereg)(lmsc, LMD_CONFIG, 0x80); */ cr = (*lmsc->lm_readreg)(lmsc, LMD_CONFIG); /* XXX - spec says *only* 0x08! */ if ((cr != 0x08) && (cr != 0x01) && (cr != 0x03) && (cr != 0x06)) return 0; DPRINTF(("%s: 0x80 check: cr = %x\n", __func__, cr)); for (i = 0; i < __arraycount(lm_chips); i++) if ((rv = lm_chips[i].chip_match(lmsc)) != 0) return rv; return 0; } int nslm_match(struct lm_softc *sc) { uint8_t chipid; /* See if we have an LM78/LM78J/LM79 or LM81 */ chipid = (*sc->lm_readreg)(sc, LMD_CHIPID) & LM_ID_MASK; switch(chipid) { case LM_ID_LM78: case LM_ID_LM78J: case LM_ID_LM79: case LM_ID_LM81: break; default: return 0; } DPRINTF(("%s: chipid %x\n", __func__, chipid)); return 1; } void lm_attach(struct lm_softc *lmsc) { uint32_t i; int rv; for (i = 0; i < __arraycount(lm_chips); i++) { if (lm_chips[i].chip_match(lmsc) != 0) { if (lm_chips[i].chip_attach(lmsc) == 0) break; else return; } } /* Start the monitoring loop */ (*lmsc->lm_writereg)(lmsc, LMD_CONFIG, 0x01); lmsc->sc_sme = sysmon_envsys_create(); /* Initialize sensors */ for (i = 0; i < lmsc->numsensors; i++) { lmsc->sensors[i].state = ENVSYS_SINVALID; if ((rv = sysmon_envsys_sensor_attach(lmsc->sc_sme, &lmsc->sensors[i])) != 0) { sysmon_envsys_destroy(lmsc->sc_sme); aprint_error_dev(lmsc->sc_dev, "sysmon_envsys_sensor_attach() returned %d\n", rv); return; } } /* * Setup the callout to refresh sensor data every 2 seconds. */ callout_init(&lmsc->sc_callout, 0); callout_setfunc(&lmsc->sc_callout, lm_refresh, lmsc); callout_schedule(&lmsc->sc_callout, LM_REFRESH_TIMO); /* * Hook into the System Monitor. */ lmsc->sc_sme->sme_name = device_xname(lmsc->sc_dev); lmsc->sc_sme->sme_flags = SME_DISABLE_REFRESH; if (sysmon_envsys_register(lmsc->sc_sme)) { aprint_error_dev(lmsc->sc_dev, "unable to register with sysmon\n"); sysmon_envsys_destroy(lmsc->sc_sme); } if (!pmf_device_register(lmsc->sc_dev, NULL, NULL)) aprint_error_dev(lmsc->sc_dev, "couldn't establish power handler\n"); } /* * Stop, destroy the callout and unregister the driver with the * sysmon_envsys(9) framework. */ void lm_detach(struct lm_softc *lmsc) { callout_halt(&lmsc->sc_callout, NULL); callout_destroy(&lmsc->sc_callout); sysmon_envsys_unregister(lmsc->sc_sme); pmf_device_deregister(lmsc->sc_dev); } static void lm_refresh(void *arg) { struct lm_softc *lmsc = arg; lmsc->refresh_sensor_data(lmsc); callout_schedule(&lmsc->sc_callout, LM_REFRESH_TIMO); } static int nslm_attach(struct lm_softc *sc) { const char *model = NULL; uint8_t chipid; /* See if we have an LM78/LM78J/LM79 or LM81 */ chipid = (*sc->lm_readreg)(sc, LMD_CHIPID) & LM_ID_MASK; switch(chipid) { case LM_ID_LM78: model = "LM78"; break; case LM_ID_LM78J: model = "LM78J"; break; case LM_ID_LM79: model = "LM79"; break; case LM_ID_LM81: model = "LM81"; break; default: return -1; } aprint_naive("\n"); aprint_normal("\n"); aprint_normal_dev(sc->sc_dev, "National Semiconductor %s Hardware monitor\n", model); lm_setup_sensors(sc, lm78_sensors); sc->refresh_sensor_data = lm_refresh_sensor_data; return 0; } static int def_match(struct lm_softc *sc) { return 1; } static int def_attach(struct lm_softc *sc) { uint8_t chipid; chipid = (*sc->lm_readreg)(sc, LMD_CHIPID) & LM_ID_MASK; aprint_naive("\n"); aprint_normal("\n"); aprint_error_dev(sc->sc_dev, "Unknown chip (ID 0x%02x)\n", chipid); lm_setup_sensors(sc, lm78_sensors); sc->refresh_sensor_data = lm_refresh_sensor_data; return 0; } static void wb_temp_diode_type(struct lm_softc *sc, int diode_type) { uint8_t regval, banksel; banksel = (*sc->lm_readreg)(sc, WB_BANKSEL); switch (diode_type) { case 1: /* Switch to Pentium-II diode mode */ lm_generic_banksel(sc, WB_BANKSEL_B0); regval = (*sc->lm_readreg)(sc, WB_BANK0_VBAT); regval |= 0x0e; (*sc->lm_writereg)(sc, WB_BANK0_VBAT, regval); regval = (*sc->lm_readreg)(sc, WB_BANK0_RESVD1); regval |= 0x70; (*sc->lm_writereg)(sc, WB_BANK0_RESVD1, 0x0); lm_generic_banksel(sc, banksel); aprint_verbose_dev(sc->sc_dev, "Pentium-II diode temp sensors\n"); break; case 2: /* Switch to 2N3904 mode */ lm_generic_banksel(sc, WB_BANKSEL_B0); regval = (*sc->lm_readreg)(sc, WB_BANK0_VBAT); regval |= 0xe; (*sc->lm_writereg)(sc, WB_BANK0_VBAT, regval); regval = (*sc->lm_readreg)(sc, WB_BANK0_RESVD1); regval &= ~0x70; (*sc->lm_writereg)(sc, WB_BANK0_RESVD1, 0x0); lm_generic_banksel(sc, banksel); aprint_verbose_dev(sc->sc_dev, "2N3904 bipolar temp sensors\n"); break; case 4: /* Switch to generic thermistor mode */ lm_generic_banksel(sc, WB_BANKSEL_B0); regval = (*sc->lm_readreg)(sc, WB_BANK0_VBAT); regval &= ~0xe; (*sc->lm_writereg)(sc, WB_BANK0_VBAT, regval); lm_generic_banksel(sc, banksel); aprint_verbose_dev(sc->sc_dev, "Thermistor temp sensors\n"); break; case 0: /* Unspecified - use default */ aprint_verbose_dev(sc->sc_dev, "Using default temp sensors\n"); break; default: aprint_error_dev(sc->sc_dev, "Ignoring invalid temp sensor mode %d\n", diode_type); break; } } static const struct wb_product * wb_lookup(struct lm_softc *sc, const struct wb_product *products, uint16_t id) { const struct wb_product *prod = products; int i = 0; while (prod[i].id != 0) { if (prod[i].id != id) { i++; continue; } if (prod[i].str == NULL) { if (products == wb_products) { if (id == WB_CHIPID_W83627DHG) { /* * Lookup wbsio_products * with WBSIO_ID. */ return wb_lookup(sc, wbsio_products, sc->sioid); } else if (id == WB_CHIPID_AS99127F) { /* * Lookup as99127f_products * with WB_VENDID. */ return wb_lookup(sc, as99127f_products, wb_read_vendorid(sc)); } else return NULL; /* not occur */ } return NULL; /* not occur */ } return &prod[i]; } /* Not found */ return NULL; } static uint16_t wb_read_vendorid(struct lm_softc *sc) { uint16_t vendid; uint8_t vendidreg; uint8_t banksel; /* Save bank */ banksel = (*sc->lm_readreg)(sc, WB_BANKSEL); /* Check default vendor ID register first */ vendidreg = WB_VENDID; retry: /* Read vendor ID */ lm_generic_banksel(sc, WB_BANKSEL_HBAC); vendid = (*sc->lm_readreg)(sc, vendidreg) << 8; lm_generic_banksel(sc, 0); vendid |= (*sc->lm_readreg)(sc, vendidreg); if ((vendidreg == WB_VENDID) && (vendid != WB_VENDID_WINBOND && vendid != WB_VENDID_ASUS)) { /* If it failed, try NCT6102 vendor ID register */ vendidreg = WB_NCT6102_VENDID; goto retry; } else if ((vendidreg == WB_NCT6102_VENDID) && (vendid != WB_VENDID_WINBOND)) vendid = 0; /* XXX */ /* Restore bank */ lm_generic_banksel(sc, banksel); return vendid; } static uint8_t wb_read_chipid(struct lm_softc *sc) { const struct wb_product *prod; uint8_t chipidreg, chipid, banksel; /* Save bank */ banksel = (*sc->lm_readreg)(sc, WB_BANKSEL); /* Check default vendor ID register first */ chipidreg = WB_BANK0_CHIPID; lm_generic_banksel(sc, WB_BANKSEL_B0); retry: (void)(*sc->lm_readreg)(sc, LMD_CHIPID); chipid = (*sc->lm_readreg)(sc, chipidreg); prod = wb_lookup(sc, wb_products, chipid); if (prod == NULL) { if (chipidreg == WB_BANK0_CHIPID) { chipidreg = WB_BANK0_NCT6102_CHIPID; goto retry; } else chipid = 0; } /* Restore bank */ lm_generic_banksel(sc, banksel); return chipid; } static int wb_match(struct lm_softc *sc) { const struct wb_product *prod; uint16_t vendid; uint8_t chipid; /* Read vendor ID */ vendid = wb_read_vendorid(sc); DPRINTF(("%s: winbond vend id 0x%x\n", __func__, vendid)); if ((vendid != WB_VENDID_WINBOND && vendid != WB_VENDID_ASUS)) return 0; /* Read device/chip ID */ chipid = wb_read_chipid(sc); DPRINTF(("%s: winbond chip id 0x%x\n", __func__, chipid)); prod = wb_lookup(sc, wb_products, chipid); if (prod == NULL) { if (vendid == WB_VENDID_WINBOND) return 1; /* Generic match */ else return 0; } DPRINTF(("%s: chipid %02x, sioid = %04x\n", __func__, chipid, sc->sioid)); return 10; /* found */ } static int wb_attach(struct lm_softc *sc) { device_t dev = sc->sc_dev; const struct wb_product *prod; const char *model = NULL; const char *vendor = "Winbond"; const struct lm_sensor *sensors; uint16_t vendid; uint8_t banksel; int cf_flags; aprint_naive("\n"); aprint_normal("\n"); /* Read device/chip ID */ sc->chipid = wb_read_chipid(sc); DPRINTF(("%s: winbond chip id 0x%x\n", __func__, sc->chipid)); if ((prod = wb_lookup(sc, wb_products, sc->chipid)) != NULL) { switch (prod->str[0]) { case 'W': vendor = "Winbond"; break; case 'A': vendor = "ASUS"; break; case 'N': vendor = "Nuvoton"; break; default: aprint_error_dev(dev, "Unknown model (%s)\n", model); return -1; } model = prod->str; sensors = prod->sensors; sc->refresh_sensor_data = wb_refresh_sensor_data; if (prod->extattach != NULL) prod->extattach(sc); } else { vendid = wb_read_vendorid(sc); if (vendid == WB_VENDID_WINBOND) { vendor = "Winbond"; model = "unknown-model"; /* Handle as a standard LM78. */ sensors = lm78_sensors; sc->refresh_sensor_data = lm_refresh_sensor_data; } else { aprint_error_dev(dev, "Unknown chip (ID %02x)\n", sc->chipid); return -1; } } cf_flags = device_cfdata(dev)->cf_flags; if (sensors != NULL) { lm_setup_sensors(sc, sensors); /* XXX Is this correct? Check all datasheets. */ switch (sc->chipid) { case WB_CHIPID_W83627EHF_A: case WB_CHIPID_W83781D: case WB_CHIPID_W83781D_2: case WB_CHIPID_W83791SD: case WB_CHIPID_W83792D: case WB_CHIPID_AS99127F: break; default: wb_temp_diode_type(sc, cf_flags); break; } } /* XXX Is this correct? Check all datasheets. */ banksel = (*sc->lm_readreg)(sc, WB_BANKSEL); switch(sc->chipid) { case WB_CHIPID_W83627THF: lm_generic_banksel(sc, WB_BANKSEL_B0); if ((*sc->lm_readreg)(sc, WB_BANK0_CONFIG) & WB_CONFIG_VMR9) sc->vrm9 = 1; lm_generic_banksel(sc, banksel); break; case WB_CHIPID_W83637HF: lm_generic_banksel(sc, WB_BANKSEL_B0); if ((*sc->lm_readreg)(sc, WB_BANK0_CONFIG) & WB_CONFIG_VMR9) sc->vrm9 = 1; lm_generic_banksel(sc, banksel); break; default: break; } aprint_normal_dev(dev, "%s %s Hardware monitor\n", vendor, model); return 0; } static void lm_setup_sensors(struct lm_softc *sc, const struct lm_sensor *sensors) { int i; for (i = 0; sensors[i].desc; i++) { sc->sensors[i].units = sensors[i].type; if (sc->sensors[i].units == ENVSYS_SVOLTS_DC) sc->sensors[i].flags = ENVSYS_FCHANGERFACT; strlcpy(sc->sensors[i].desc, sensors[i].desc, sizeof(sc->sensors[i].desc)); sc->numsensors++; } sc->lm_sensors = sensors; } static void lm_refresh_sensor_data(struct lm_softc *sc) { int i; for (i = 0; i < sc->numsensors; i++) sc->lm_sensors[i].refresh(sc, i); } static void lm_refresh_volt(struct lm_softc *sc, int n) { int data; data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg); if (data == 0xff) { sc->sensors[n].state = ENVSYS_SINVALID; } else { sc->sensors[n].value_cur = (data << 4); if (sc->sensors[n].rfact) { sc->sensors[n].value_cur *= sc->sensors[n].rfact; sc->sensors[n].value_cur /= 10; } else { sc->sensors[n].value_cur *= sc->lm_sensors[n].rfact; sc->sensors[n].value_cur /= 10; sc->sensors[n].rfact = sc->lm_sensors[n].rfact; } sc->sensors[n].state = ENVSYS_SVALID; } DPRINTF(("%s: volt[%d] data=0x%x value_cur=%d\n", __func__, n, data, sc->sensors[n].value_cur)); } static void lm_refresh_temp(struct lm_softc *sc, int n) { int data; /* * The data sheet suggests that the range of the temperature * sensor is between -55 degC and +125 degC. */ data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg); if (data > 0x7d && data < 0xc9) sc->sensors[n].state = ENVSYS_SINVALID; else { if (data & 0x80) data -= 0x100; sc->sensors[n].state = ENVSYS_SVALID; sc->sensors[n].value_cur = data * 1000000 + 273150000; } DPRINTF(("%s: temp[%d] data=0x%x value_cur=%d\n", __func__, n, data, sc->sensors[n].value_cur)); } static void lm_refresh_fanrpm(struct lm_softc *sc, int n) { int data, divisor = 1; /* * We might get more accurate fan readings by adjusting the * divisor, but that might interfere with APM or other SMM * BIOS code reading the fan speeds. */ /* FAN3 has a fixed fan divisor. */ if (sc->lm_sensors[n].reg == LMD_FAN1 || sc->lm_sensors[n].reg == LMD_FAN2) { data = (*sc->lm_readreg)(sc, LMD_VIDFAN); if (sc->lm_sensors[n].reg == LMD_FAN1) divisor = (data >> 4) & 0x03; else divisor = (data >> 6) & 0x03; } data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg); if (data == 0xff || data == 0x00) sc->sensors[n].state = ENVSYS_SINVALID; else { sc->sensors[n].state = ENVSYS_SVALID; sc->sensors[n].value_cur = 1350000 / (data << divisor); } DPRINTF(("%s: fan[%d] data=0x%x value_cur=%d\n", __func__, n, data, sc->sensors[n].value_cur)); } static void wb_refresh_sensor_data(struct lm_softc *sc) { uint8_t banksel, bank; int i; /* * Properly save and restore bank selection register. */ banksel = bank = sc->lm_readreg(sc, WB_BANKSEL); for (i = 0; i < sc->numsensors; i++) { if (bank != sc->lm_sensors[i].bank) { bank = sc->lm_sensors[i].bank; lm_generic_banksel(sc, bank); } sc->lm_sensors[i].refresh(sc, i); } lm_generic_banksel(sc, banksel); } static void wb_w83637hf_refresh_vcore(struct lm_softc *sc, int n) { int data; data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg); /* * Depending on the voltage detection method, * one of the following formulas is used: * VRM8 method: value = raw * 0.016V * VRM9 method: value = raw * 0.00488V + 0.70V */ if (sc->vrm9) sc->sensors[n].value_cur = (data * 4880) + 700000; else sc->sensors[n].value_cur = (data * 16000); sc->sensors[n].state = ENVSYS_SVALID; DPRINTF(("%s: volt[%d] data=0x%x value_cur=%d\n", __func__, n, data, sc->sensors[n].value_cur)); } static void wb_refresh_nvolt(struct lm_softc *sc, int n) { int data; data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg); sc->sensors[n].value_cur = ((data << 4) - WB_VREF); if (sc->sensors[n].rfact) sc->sensors[n].value_cur *= sc->sensors[n].rfact; else sc->sensors[n].value_cur *= sc->lm_sensors[n].rfact; sc->sensors[n].value_cur /= 10; sc->sensors[n].value_cur += WB_VREF * 1000; sc->sensors[n].state = ENVSYS_SVALID; DPRINTF(("%s: volt[%d] data=0x%x value_cur=%d\n", __func__, n , data, sc->sensors[n].value_cur)); } static void wb_w83627ehf_refresh_nvolt(struct lm_softc *sc, int n) { int data; data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg); sc->sensors[n].value_cur = ((data << 3) - WB_W83627EHF_VREF); if (sc->sensors[n].rfact) sc->sensors[n].value_cur *= sc->sensors[n].rfact; else sc->sensors[n].value_cur *= RFACT(232, 10); sc->sensors[n].value_cur /= 10; sc->sensors[n].value_cur += WB_W83627EHF_VREF * 1000; sc->sensors[n].state = ENVSYS_SVALID; DPRINTF(("%s: volt[%d] data=0x%x value_cur=%d\n", __func__, n , data, sc->sensors[n].value_cur)); } static void wb_refresh_temp(struct lm_softc *sc, int n) { int data; /* * The data sheet suggests that the range of the temperature * sensor is between -55 degC and +125 degC. However, values * around -48 degC seem to be a very common bogus values. * Since such values are unreasonably low, we use -45 degC for * the lower limit instead. */ data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg) << 1; data += (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg + 1) >> 7; if (data > 0xfffffff || (data > 0x0fa && data < 0x1a6)) { sc->sensors[n].state = ENVSYS_SINVALID; } else { if (data & 0x100) data -= 0x200; sc->sensors[n].state = ENVSYS_SVALID; sc->sensors[n].value_cur = data * 500000 + 273150000; } DPRINTF(("%s: temp[%d] data=0x%x value_cur=%d\n", __func__, n , data, sc->sensors[n].value_cur)); } static void wb_refresh_fanrpm(struct lm_softc *sc, int n) { int fan, data, divisor = 0; /* * This is madness; the fan divisor bits are scattered all * over the place. */ if (sc->lm_sensors[n].reg == LMD_FAN1 || sc->lm_sensors[n].reg == LMD_FAN2 || sc->lm_sensors[n].reg == LMD_FAN3) { data = (*sc->lm_readreg)(sc, WB_BANK0_VBAT); fan = (sc->lm_sensors[n].reg - LMD_FAN1); if ((data >> 5) & (1 << fan)) divisor |= 0x04; } if (sc->lm_sensors[n].reg == LMD_FAN1 || sc->lm_sensors[n].reg == LMD_FAN2) { data = (*sc->lm_readreg)(sc, LMD_VIDFAN); if (sc->lm_sensors[n].reg == LMD_FAN1) divisor |= (data >> 4) & 0x03; else divisor |= (data >> 6) & 0x03; } else if (sc->lm_sensors[n].reg == LMD_FAN3) { data = (*sc->lm_readreg)(sc, WB_PIN); divisor |= (data >> 6) & 0x03; } else if (sc->lm_sensors[n].reg == WB_BANK0_FAN4 || sc->lm_sensors[n].reg == WB_BANK0_FAN5) { data = (*sc->lm_readreg)(sc, WB_BANK0_FAN45); if (sc->lm_sensors[n].reg == WB_BANK0_FAN4) divisor |= (data >> 0) & 0x07; else divisor |= (data >> 4) & 0x07; } data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg); if (data >= 0xff || data == 0x00) sc->sensors[n].state = ENVSYS_SINVALID; else { sc->sensors[n].state = ENVSYS_SVALID; sc->sensors[n].value_cur = 1350000 / (data << divisor); } DPRINTF(("%s: fan[%d] data=0x%x value_cur=%d\n", __func__, n , data, sc->sensors[n].value_cur)); } static void wb_nct6776f_refresh_fanrpm(struct lm_softc *sc, int n) { int datah, datal; datah = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg); datal = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg + 1); if ((datah == 0xff) || (datah == 0)) { sc->sensors[n].state = ENVSYS_SINVALID; } else { sc->sensors[n].state = ENVSYS_SVALID; sc->sensors[n].value_cur = (datah << 8) | datal; } } static void wb_w83792d_refresh_fanrpm(struct lm_softc *sc, int n) { int shift, data, divisor = 1; uint8_t reg; shift = 0; switch (sc->lm_sensors[n].reg) { case 0x28: reg = 0x47; shift = 0; break; case 0x29: reg = 0x47; shift = 4; break; case 0x2a: reg = 0x5b; shift = 0; break; case 0xb8: reg = 0x5b; shift = 4; break; case 0xb9: reg = 0x5c; shift = 0; break; case 0xba: reg = 0x5c; shift = 4; break; case 0xbe: reg = 0x9e; shift = 0; break; default: reg = 0; break; } data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg); if (data == 0xff || data == 0x00) sc->sensors[n].state = ENVSYS_SINVALID; else { if (reg != 0) divisor = ((*sc->lm_readreg)(sc, reg) >> shift) & 0x7; sc->sensors[n].state = ENVSYS_SVALID; sc->sensors[n].value_cur = 1350000 / (data << divisor); } DPRINTF(("%s: fan[%d] data=0x%x value_cur=%d\n", __func__, n , data, sc->sensors[n].value_cur)); } static void as_refresh_temp(struct lm_softc *sc, int n) { int data; /* * It seems a shorted temperature diode produces an all-ones * bit pattern. */ data = (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg) << 1; data += (*sc->lm_readreg)(sc, sc->lm_sensors[n].reg + 1) >> 7; if (data == 0x1ff) sc->sensors[n].state = ENVSYS_SINVALID; else { if (data & 0x100) data -= 0x200; sc->sensors[n].state = ENVSYS_SVALID; sc->sensors[n].value_cur = data * 500000 + 273150000; } DPRINTF(("%s: temp[%d] data=0x%x value_cur=%d\n", __func__, n, data, sc->sensors[n].value_cur)); } MODULE(MODULE_CLASS_DRIVER, lm, "sysmon_envsys"); static int lm_modcmd(modcmd_t cmd, void *opaque) { switch (cmd) { case MODULE_CMD_INIT: case MODULE_CMD_FINI: return 0; default: return ENOTTY; } }